M6 dropped, won't switch on [FIXED]

So I dropped my M6 player (about a meter) and now it won't turn on. ie. the power button usually clicks when pressed down, but now it just doesn't click.
I also have a feeling that the button is lower than usual (ie. kinda half pressed in already).

I think the player still works as I am able to charge it fully. Any Ideas?

Also held down Enter button for 30 seconds, no luck but I wasn't expecting much there.

This has happened to me. I think you will find that the power button has snapped off the mainboard at the solder points. I fixed it myself with not to much difficulty by re-attaching it with a soldering iron and it has worked perfectly since. If you do not feel up to tackling it your self any electronics technician (like mobile phone repair) should be able to fix it in no time.

Thanks mate, any idea how I can pry open the faceplate? I've tried with a small screwdriver but so far no luck.
Anything else I should look out for when soldering?

There are 8 locking points three on either side and one on either side of the USB\Earphone hub so it is easier to start at the end where there are no lock tabs. The arrows show the points where you may find it easier to start to open the player.



A screwdriver is possibly not the best tool as I think you have a very real chance of damaging the faceplate. Hold the player as in the picture and force the thumbnail of your free hand into the top corner, once you have it wedged between just sliding your thumbnail around the player should be enough to pop the locking tabs as you go.



Once you have the player open you need to remove the 2 screws holding the mainboard.



Once you have the mainboard free you should find the power switch floating around, put it to one side. You will notice that there are 2 ribbon cables connected to the mainboard, one for the touch control and one for the LCD, you need to disconnect them. This is quite simple to do, start with the smaller touch strip one and follow it to the mainboard connector you will see a brown tab, this is hinged and can be flipped up with a fine tipped screwdriver to release the ribbon cable which you can then slide out of the connector. Repeat the process with the LCD ribbon cable.



Once you have the mainboard free arrange it on a non metalic surface so that it is sitting level. Heat up your soldering iron and apply a drop of solder to the tip.



Using a pair of tweezers align the power switch to the mainboard at the broken solder points ( Be sure it is facing the right way). Hold the switch in place with the tweezers and apply the drop of solder to one side of the switch and hold the iron there for a few seconds so that it heats and bonds with the existing solder on the connection. Allow for the solder to set and then repeat the process on the other side connection point. Try to avoid actually touching the soldering iron to the switch, the drop of solder should be hot enough to bond the connection without risking heat stressing the components.



Once you have the switch securely soldered reconnect the ribbon cables by sliding them back into the connector and pressing down the locking tab. Try to avoid excessive flexing\bending of the ribbon cable. Once you have done this you can test the switch before replacing the screws.

If all went well your player should power up as normal. Switch it off, replace the screws, and gently press the metal backplate into place. Do not force the player back together, if you are having difficulty remove and realign the cover and try again.



Disclaimer: This information is provided for informative purposes only. All electronic repairs should be done by trained professionals. You take full responsibility for opening and attempting any repairs to your player. I will not be responsible for any damage that may occur as a result attempting any of the above. As always when handling electronic components an anti-static wrist strap should be used. It is also good practice to disconnect the battery before commencing any repairs.

Thank you madman, for this detailed instruction.
It will surely help those who want to repair the device themselves.
Now i've got an idea how to open it, if necessary.

Yeah...really appreciate the detail photos as well.

Will let you know how I go...perhaps this should be stickied?

Nice photos!

I'm assuming that one could follow these directions to replace the batter as well? Do you know where to get a new battery?

I'm assuming that one could follow these directions to replace the batter as well? Do you know where to get a new battery?

You can not buy replacement batteries for the M6 as they are not a standard size. I emailed Meizu Global Support a couple of weeks ago and the only way to get a replacement is to send the player back to them and they will replace it.

Thanks for your email.

May we know where you bought mini player? What's its S/N?

If replace battery, then you need to send the player back to us, and pay the
cost of battery. To save your transportation cost, would you contact the
retailer to send it back?

Thank you and best regards,


MEIZU

Mate, you are my hero. The guide worked like a charm, was a bit tricky opening the faceplate and my MEIZU is a bit battered now but after that it was just following your guide step-by-step.

Now I have my MEIZU back. Really appreciate it.

Cool, glad it helped. Sorry to hear you had trouble opening the player though I hope it isn't to badly marked. Perhaps because I have opened mine a few times it is a little easier.

Just out of curiosity was your player in a crystal case when you dropped it, I recall another post sometime ago from someone with the same problem and they were using a crystal case as I was, just wondering if this happens because of the button extender on the case. Seems to be a bit of a weak spot though.

Still love my Meizu though and hanging out for the M6SE.

Originally Posted by /\/\@D/\/\@/\/

Cool, glad it helped. Sorry to hear you had trouble opening the player though I hope it isn't to badly marked. Perhaps because I have opened mine a few times it is a little easier.

Just out of curiosity was your player in a crystal case when you dropped it, I recall another post sometime ago from someone with the same problem and they were using a crystal case as I was, just wondering if this happens because of the button extender on the case. Seems to be a bit of a weak spot though.

Still love my Meizu though and hanging out for the M6SE.

Thank goodness for you!! Whatever your name is.......

Originally Posted by /\/\@D/\/\@/\/

Just out of curiosity was your player in a crystal case when you dropped it,

Nah, my Meizu looks like the first photo you posted.

Originally Posted by RockRacer

Thank goodness for you!! Whatever your name is.......

I think his name is Madman and yes great work!

Wohooo.Great!!
Last Week I wasn`t able to start my Meizu M6.First I was so angry that I wanted to throw that damn thing against the next wall.
Then I searched here in the Forum and found this thread.So I used madman's guide.It was the first time I soldered - but it works.Now I have my Meizu back!!!! :eek: Thank you so much for your excellent guide madman!!

I was already on to buy a new mp3 player...

Thank you madman!! You're my hero!! :D